english version of install

I need an english language version on intcon 2_3. Is there 1 available?
My German lang version is having install trouble and I don't know German.

IntCon can be switched to English. However, the installation is German only. If you have troubles during the installation process, please contact the support via email.

Zitat Admin
IntCon can be switched to English. However, the installation is German only. If you have troubles during the installation process, please contact the support via email.

I contacted support, whlie they were willing to help, I still had trouble with trying to type out the German text on the screen.
I can get InitCon to work by just running the program from a folder from the compressed .cab file.
Thanks...

Hello
Recently received USB-Interface III (without cord) (USB-Int3)

I am installing it on an English version of Windows XP.

this error message is reported:

'MFTech Int-Setup wurden unter brochen, bevor die software vollstandig installiert werden konnte.
Sie konnen das MFTech Int-Setup spater vollstandig wederholen, um die Installation zu abzuschliessen"
(I do not read German unfortunately - what does this mean ???)

As was posted I tried extracting the cab file and running the exe (Intcon Application) but this does not install the program (place dlls in correct location, change registry, etc.)
This starts the IntCon v2.3 MFTech R/C USB Interface Config, but it dose not appear to connect via the USB III interface with my RC transmitter?
(I have checked the transmitter with an oscilliscope and the signals are being transmitted via the buddy cable to the USB III interface).

When i open the FMS silmulator the USB-RC is not an option as a control device.

I believe that the software is NOT correctly installed.

ANY BODY HELP PLEASE,

thank you,
Gabriel <!-- s:( --><img src="{SMILIES_PATH}/icon_sad.gif" alt=":(" title="Sad" /><!-- s:( -->

This message says that the installation procedure was interrupted before its completion. IntCon runs if you just extract the complete content of the cab-file into a directory and run intcon.exe, limitation: no firmware-update possible. It should show you all USB HID devices in the start screen. IntCon has no problem with an English Windows installation.
Maybe regsvr32 ebCrypt.dll helps you. Does your system have problems with other programs based on Visual Basic 6.0 technology?
Maybe an older version of IntCon helps, see here: http://www.mftech.de/cgi-bin/versioncheck.pl

Hello Thanks for the response,

The USB III interface is still not working <!-- s:? --><img src="{SMILIES_PATH}/icon_confused.gif" alt=":?" title="Confused" /><!-- s:? -->


A)
Control panel -> game controller -> RC_USB
Brings up RC_USB Properties
There are 2 panels Test and Settings, neither of these changes when I move the controls on the RC transmitter.

B)
In FMS -> Control -> Analogue Controls -> Joystick Interface -> Mapping Calibration Move the controls on the RC transmitter does not make any changes

C)
I copied ebCrypt.dll into the WINDOWS\system32 folder and ran regsvr32 ebCrypt.dll, which ran successfully. However there appears to be no change. The interface still did not appear to be working.
I reran the setup program which appeared to go through installation 42 steps and request a restart of the computer.
After the restart the RC transmitter is still not being read.

I had already extracted the contents of the .cab file into a directory I created: Program Files\IntCon. Should these be copied to a different directory?

D)
I purchased a USB interface III and a connector for a Futaba 6 pole square. However I am using a Futaba 6 (T6YG) with a round 6 pole connector. | have made up a buddy cable with a 6 pole round on one end and a mono jack on the other. It is wired as described on your web site.
I have checked it with an oscilloscope and the tip of the mono jack has the signal, while the shaft of the mono jack is ground. The signal varies when I move any of the controls on the RC transmitter.

E)
When I insert the USB III interface the red led stays on for about 2 seconds then goes out. I then power up the RC transmitter. The Crystal is removed from the RC transmitter.
And as I said moving the controls on the RC transmitter makes no difference on the computer end.

F)
When I run the Intcon application I get the program: Intcon V2.3 – MFTech R/C USB-Interface Config program. Selecting the RC by MFTech opens the: Configuration FW 1.3.23 pannel. Moving the controls on the RC transmitter makes no difference to this screen everything stays the same.

What can I do ? Is it broken or ?

Your help would be very much appreciated.
Thank you,
Gabriel

The problem was a bad contact between the transmitter cord and the receiver cord. After fixing the connection, everything was fine. Thanks to the customer since he found out the problem by himself and fixed it